Mazda 323
+ Introduction
+ Petrol engines
+ System of greasing of the engine
+ System of cooling of the engine
+ ignition System
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and steering system
+ Brake system
- Wheels and tires, body, car coloring, care of the car
The sizes of disks and tires/pressure in tires
Designations of disks
Designations of tires
Replacement of wheels
Rules of care of tires
Balancing of wheels
Antisliding chains
Spare wheel
Wear of tires
Body
Removal and installation of a front bumper
Removal and installation of a rear bumper
Removal and front grille installation
Removal and installation of lateral moldings
Removal and installation of a forward wing
Removal and cowl installation/adjustment
Removal and installation/adjustment of a door of a back
Removal and door installation/adjustment
Upholstery door door/window regulator/glass
Removal and installation of an upholstery of a door
Removal and installation of a glass/window regulator of a forward door
Lock/handle/cylinder of the lock of a door
Lock of a door of a back / internal drive
External mirror
Removal and installation of glass of a mirror
Panel of devices / average console
Forward seats
Removal and installation of a back seat
Back seat
Car coloring
Elimination of damages from stones
Rikhtovka body/repair of rusty openings
Preparation for painting
Coloring
Wash of the car
Care of a varnish covering
Protection of the bottom and preservation of cavities
Care of an upholstery
+ electric equipment System
+ Heater, lighting system, devices
+ Governing bodies and operation receptions
+ Electric circuits
|
Removal and installation of a forward wing
MAZDA 323 from 10/89 g вып.
Removal
|
|
To change the provision of a disk of a wheel concerning a nave that it was possible to establish an otbalansirovanny wheel in former situation.
To weaken nuts of a wheel of the car standing on the earth.
To lift a forward part of the car.
To remove a wheel.
To remove the forward index of turn-1-, see. Head Heater, lighting system, devices.
To remove a front grille-2-, and also an overlay of a lattice, Head of the Wheel and the tire, a body, car coloring, care of the car.
To remove a headlight-3-, Head the Heater, lighting system, devices.
To unscrew a gryazeulovitel-4-.
To turn out bolts of a loker-5-from within, to wring out a loker from a wing and to take out.
Because of protective mastic and a sealing tape the wing sits very strongly. The hair dryer reaching, at least, a temperatures +450°С is necessary for weakening of fastening of a wing. If the hair dryer is not present, it is recommended to cut off protective mastic in junctions a knife.
|
|
To heat up vinyl protective mastic the bottoms (material PVC) slightly and short time. PVC color should not change and should not be formed swellings. Otherwise there are evaporations hazardous to health, hydrochloric acid bringing to corrosion is besides formed. |
Carefully step by step to remove a wing.
|
|
Installation
|
|
If necessary to paint a wing.
To clear surfaces of a prileganiye of a wing, if necessary отрихтовать.
To cover points of fastening of bolts of fastening of a wing in a wheel arch and a forward rack of a body with anticorrosive means.
To impose on prileganiye surfaces a standard tape for consolidation of wings.
To establish, level and screw a wing. Thus to watch a uniform gap between a cowl and a wing, and also a door and a wing.
|
|
Fastening bolts (саморезы) can be tightened with effort of 10 Nanometers, i.e. it is absolutely easy. |
To put on wing inside mastic of protection of the bottom.
To condense a loker on a wing with hermetic.
To screw a gryazeulovitel.
To establish a front grille and a decorative slip.
To establish a headlight and the turn index. To adjust headlights.
To establish a wheel, considering a label on a nave. To lower the car and to tighten wheel nuts cross-wise with effort of 100 Nanometers.
|
|
|
|