Mazda 323
+ Introduction + Petrol engines + System of greasing of the engine + System of cooling of the engine + ignition System + Power supply system, carburetor, system of injection of fuel + Diesel engine + System of production of the fulfilled gases + Coupling + Manual transmission + Automatic transmission + Suspension bracket and steering system + Brake system + Wheels and tires, body, car coloring, care of the car + electric equipment System + Heater, lighting system, devices - Governing bodies and operation receptions Before landing in the car Running in Keys Locks of doors The uniform (central) locking device (if is available) Protection against pranks of children (if is available, only on back doors) Electric window regulator (if is available) Back rotary glasses (on 3-door models) Seats Adjustment of height of a steering wheel (if is available) Seat belts (if is available) Door back/trunk lid Fuelling Mirrors Luggage belts Trunk lid (if is available) Spare wheel Dashboard - Steering wheel and gear shifting Lock of ignition and steering column Engine start Management of RKPP and transfer case Car operation with an automatic transmission Recommendations for economic operation Tempostat (switch of a mode of maintenance of constant speed) Lighting and light alarm system Screen wiper and stekloomyvatel Control panel Other devices and equipment Heater and ventilation The conditioner (if is available) Lamps of salon, luggage carrier and lamp for reading (if is available) The movable hatch (if is available) Start by pushing or towage Impellent compartment + Electric circuits
|
Engine start The cars which have not been equipped with electric system of injection of fuel
|
Fasten a seat belt.
Check, whether will tighten the hand brake.
Manual transmission – completely squeeze out coupling and establish the switching lever in neutral situation. At start hold a coupling pedal in completely squeezed out situation.
Automatic transmission – establish the box lever in the situation "R" (parking) or «N» (neutral).
|
Do not hold a starter of 10 seconds included more long. If the engine is not started at once, wait for 5-10 seconds, and repeat start process, differently a starter it can be damaged. |
|
|
Cars without a manual drive of an air zaslonka
Cold engine
|
Once completely squeeze out a pedal of gas and release.
Turn the ignition key in the situation "START (III)". Release its maximum in 10 seconds.
Squeeze out a gas pedal approximately to a half if the engine is started. Release a gas pedal to lower number of turns.
Let's to the engine get warm approximately within 10 seconds before transfer inclusion.
On a frost (below – 18°С) or if the car was not used some days
Squeeze out a gas pedal two-three times and again release it.
Turn the ignition key in the situation "START (III)". Release a key when the engine will be started.
If the engine is not started, release the ignition key. Squeeze out a gas pedal five-ten times before the following attempt of start.
Turn the ignition key in the situation "START (III)" to start the engine.
When the engine will be started, let's to it get warm, without pressing a gas pedal.
If the engine in 30 seconds earns evenly, lower number of turns in easy pressing and an otpuskaniye of a pedal of gas.
|
If the engine long time (more than 5 minutes) idles with the raised number of turns, the car can be damaged because of very high temperature of system of purification of the fulfilled gases. |
|
|
Warm engine
|
Squeeze out a gas pedal half and hold in this situation, without pumping over.
Turn the ignition key in the situation "START (III)" to start the engine.
Release the ignition key and a gas pedal when the engine will be started.
|
|
Candles are filled in with fuel
|
If the hot engine is not started, maybe, that candles are filled in with fuel. Therefore wait at least half-minute before the following attempt of start.
Completely squeeze out a pedal of gas and hold her in this situation without pumping over.
Turn the ignition key in the situation "START (III)" to start the engine.
Release the ignition key and a gas pedal when the engine will be started.
|
|
For cars with a manual drive of an air zaslonka
Air zaslonka
|
Extend a drive of an air zaslonka only for start or engine warming up.
Completely extend the button of an air zaslonka.
|
When the engine will reach the working temperature, completely move the button.
|
|
|
Control lamp of an air zaslonka (if is available)
|
The control lamp lights up, when the button of an air zaslonka is extended and dies away at a button vdviganiye. |
On the cold engine
|
|
Do not squeeze out a gas pedal.
|
Completely extend the button of an air zaslonka.
Turn the ignition key in the situation "START (II)".
Release the ignition key when the engine will be started. If the engine decays, once again start it.
After start of the engine move the button so that the engine worked steadily.
When the engine will reach the working temperature, completely move the button of an air zaslonka.
|
|
On the warm engine
|
|
Squeeze out a gas pedal approximately half. Do not pump over a pedal of gas and do not extend the button of an air zaslonka.
|
Turn the ignition key in the situation "START (III)".
After start of the engine release the ignition key and slowly release a gas pedal.
|
|
Candles are filled in with fuel
|
|
If on the warm engine of a candle are filled in with fuel and it is not started, wait 1 minute or more long before repeating start attempt.
|
Slowly completely squeeze out a gas pedal. Do not pump over and do not extend the button of an air zaslonka.
Turn the ignition key in the situation "START (III)" to start the engine.
After start of the engine release the ignition key and slowly release a gas pedal.
|
If the engine is not started because of superfluous fuel, remove candles and dry them. |
|
Do not allow finding of cigarets, sparks or open fire near the engine at replacement of candles. |
|
|
The cars equipped with electric system of injection of fuel
|
Fasten a seat belt (if is available).
Check, whether will tighten the hand brake.
Do not squeeze out a gas pedal.
Completely squeeze out a pedal of coupling and establish the gear shifting lever in neutral situation
Start the engine at the squeezed-out coupling.
Turn the ignition key in the situation "START (III)".
Release the ignition key when the engine will be started. If the engine decays, once again start it.
|
On the warm or cold engine at first try to start it, without squeezing out a gas pedal. If the warm engine is not started, squeeze out a gas pedal half and once again start. |
|
|
Only for engines with a turbokompressor
|
Directly after a trip since high speed or after long lifting the engine should work with number of turns of idling of at least 30 seconds before it will be stopped. |
Diesel engine
|
Fasten a seat belt (if is available).
Check, whether will tighten the hand brake.
Completely squeeze out a pedal of coupling and establish the transmission lever in neutral situation. During start hold a coupling pedal in completely squeezed out situation.
|
Do not hold a starter of 30 seconds included more long. If the engine is not started at once, wait for 5-10 seconds, and repeat start process, differently a starter it can be damaged. |
|
|
On the cold engine
|
|
Turn the ignition key in the situation "ON (II)".
|
Then turn the ignition key in the situation "START (III)" and start the engine, without squeezing out a gas pedal. On the cold engine the gas pedal at start of the engine should be squeezed completely out.
|
- At low temperatures of air completely extend the button of cold start, turn to the right and turn the ignition key in the situation "ON (II)".
- Turn the ignition key in the situation "START (III)" and hold, while the engine will not be started. Squeeze out a gas pedal a little to raise number of turns, and release it when the engine will steadily work.
- Turn the button of cold start to the left and completely move it when the engine will reach the usual working temperature.
- During engine warming up the button of cold start should be extended.
|
|
For simplification of start switch off all electrodevices. - If the engine is not started, return the ignition key to the situation "LOCK (0)" or "ACC (I)" before making new attempt of start.
| | | On the warm engine
|
Turn the ignition key in the situation "ON (II)".
Then turn the ignition key in the situation "START (III)" and start the engine, without squeezing out a gas pedal.
|
|
|
|