Mazda 323

since 1985 of release

Repair and car operation


Mazda 323

- Introduction
   About this Management
   Mazda-323 brand cars — the introduction
   Identification numbers of the car
   Acquisition of spare parts
   Technology of service, tools and workplace equipment
   Engine start from an auxiliary source
   Poddomkrachivaniye and towage
   Automobile himikaliya, oils and greasings
   Diagnostics of malfunctions
   Routine maintenance
   - Works on maintenance
      Oil replacement
      Replacement of the oil filter
      Replacement of the perepuskny oil filter
      Visual check on leakage of oil
      Check of level of engine oil
      Check of level of cooling liquid
      Replacement of cooling liquid
      Visual check of tightness of system of cooling
      Frost resistance check
      Adjustment of gaps of valves
      Pulling up of bolts of a head of cylinders
      Pulling up of bolts of inlet and final collectors
      Check of the sensor of provision of a butterfly valve
      Check of the moment of ignition
      Replacement of candles ignition/check of electric contacts
      Replacement of an element of the air filter
      Plums of a sediment of the fuel filter diesel engine/replacement of the fuel filter
      Check maple belt/tension/replacement of a gear belt
      Visual check of system of production of the fulfilled gases
   + Box transfers/drive of wheels
   + brakes/tyres/wheels
   + Steering management/drive of forward wheels
   + car Electric equipment
   + Body / internal equipment
+ Petrol engines
+ System of greasing of the engine
+ System of cooling of the engine
+ ignition System
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and steering system
+ Brake system
+ Wheels and tires, body, car coloring, care of the car
+ electric equipment System
+ Heater, lighting system, devices
+ Governing bodies and operation receptions
+ Electric circuits



Replacement of candles ignition/check of electric contacts

The special tool is required:

    Candle key. It is in addition recommended to buy special nippers, for example, HAZET 1849 for simplification of removal of tips of candles.

The following spare parts should be bought:

Removal

 PERFORMANCE ORDER

    To disconnect all tips of candles, thus it is necessary to pull for tips, instead of for cables. Aforementioned nippers facilitate removal. To blow niches of candles the compressed air that at the removed candles dirt could not get to openings. To turn out candles a candle key and to check a condition of candles (appearance). In the presence of some experience it is possible to draw conclusions on an engine condition from this:

Electrodes and insulators

The average-gray — the correct work сечи ignitions and quality of a mix

The black — a mix too rich

The light gray — a mix too poor

Are greasy — interruptions in work of the corresponding candle or a low insulation of piston rings (to check a compression).

 PERFORMANCE ORDER

    To check insulators of candles on superficial currents of leak. Superficial currents leave thin, non-uniform traces on a surface. Probably it is required to replace not tight tips of candles.

Installation

 PERFORMANCE ORDER

    Before installation to check distance between electrodes by means of flat щупа.
    At new candles the distance between electrodes is, as a rule, established correctly, see. Head ignition System, the Candle Section for MAZDA 323.
    For distance adjustment between contacts it is necessary to turn in a weight electrode. For this purpose there is a simple, practical adaptation, otherwise to knock on a weight electrode. At a podgibaniye to rest a small screw-driver against a candle carving, at all in the central electrode as differently it will be damaged.
    To clear a carving on candles a pure rag. To screw in spark plugs a hand to a prileganiye to a head of cylinders.

Candle thus not to warp.

    To tighten spark plugs with effort of 20 Nanometers.

If there is no dinamometrichesky key, to tighten new spark plugs a candle key on 90 ° (1/4 turns). The candles which were in the use to tighten only on 15 °. The too strongly tightened candles can break or damage at a vyvinchivaniye a carving in a head of cylinders. In this case to make carving repair by repair loose leaves of UTC or Heli - Coil.

    To connect tips of candles according to an order of ignition 1-3-4-2. To check durability of landing of tips of candles and ignition cables.

Check of electric sockets

 PERFORMANCE ORDER

    To check durability of landing of all electric sockets on the ignition coil. The burst plugs to replace. To clear korrodirovanny contacts by a wire brush or a skin, if necessary to spray spray for contacts. Contacts should not be damp, otherwise clear contacts and spray spray for contacts. To bend cables of ignition and to check existence of cracks. If necessary to replace all cables of ignition.