Mazda 323

since 1985 of release

Repair and car operation



Mazda 323

+ Introduction
+ Petrol engines
+ System of greasing of the engine
+ System of cooling of the engine
+ ignition System
- Power supply system, carburetor, system of injection of fuel
   Purity rules at work with a power supply system
   Removal and sensor installation/check in a fuel tank
   Removal and installation of a fuel tank
   Removal and installation of the fuel pump
   Removal and installation/check of the fuel pump
   Removal and installation of the air filter
   + Carburettor
   + System of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and steering system
+ Brake system
+ Wheels and tires, body, car coloring, care of the car
+ electric equipment System
+ Heater, lighting system, devices
+ Governing bodies and operation receptions
+ Electric circuits




Removal and installation of a fuel tank

Fuel tank (The injector engine)

1 — a cover of the fuel pump
2 — the tip of the fuel pump
3 — fuel hoses
4 — the fuel pump with the level sensor
5 — hoses of ventilation of a tank
6 — a hose of a jellied mouth

7 — a fuel tank guard
8 — tape holders of a tank
9 — a fuel tank
10 — a jellied mouth of a fuel tank
11 — the dvukhkhodovy return valve

The fuel tank depending on model and year of release can have volume from 48 to 55 liters and is made of sheet steel. It is located in the field of a back suspension bracket under a body.

Removal

At removal of a fuel tank a fuel quantity can act. Pairs of fuel are poisonous, therefore it is necessary to provide good ventilation of a room. To avoid fuel hit on skin. To work in toplivostoyky mittens.

Not to work near open fire! To keep in readiness the fire extinguisher!


 PERFORMANCE ORDER

    To disconnect a weight cable from the battery.

Data from memory of malfunctions of the engine or protective code of a radio receiver are thus erased. Before shutdown of the battery it is necessary to read instructions in the Section Removal and battery installation.

    To remove a back seat, see. Head of the Wheel and tire, body, car coloring, care of the car. To unscrew a cover of the fuel pump and to disconnect the tip. To weaken shlangovy collars and to disconnect fuel hoses. For simplification of installation to mark hoses with a sticky tape. To lift the car. To turn out a drain stopper of a fuel tank and to merge fuel in a pure vessel. After fuel will flow down, to establish and tighten a drain stopper.
    To disconnect fuel, ventilating hoses and a hose of a jellied mouth. For simplification of installation to mark hoses with a sticky tape.
    To unscrew a guard of a fuel tank. To unscrew bolts of fastening of tape holders of a tank, slowly to lower a tank. To check, whether all pipelines and hoses are blocked. To take out a fuel tank. If it is required to remove a jellied pipe, to weaken a bolt of fastening and to remove a pipe down.

Installation

 PERFORMANCE ORDER

    If it is removed, to establish a jellied mouth and to tighten a fastening bolt with effort of 10 Nanometers.
    To establish a fuel tank, to put on a rubber hose of a bulk mouth the union a minimum on 35 mm and to fix a new collar.
    To connect fuel and ventilating hoses according to marking.

All hoses should be put on unions at least on 25 mm.

    To establish holders of a fuel tank and to screw them with effort of 50 Nanometers. To lay топливопроводы so that they were not flattened or bent. To establish a guard of a tank and to screw with effort of 10 Nanometers. To lower the car. To connect топливопроводы to the fuel pump according to marking and to fix collars. To connect tips of the fuel pump and to screw a pump cover. To establish a back seat, see. Head of the Wheel and tire, body, car coloring, care of the car. To connect a weight cable to the battery. If are available, to establish time on hours and to set a protective code of a radio receiver. To check work of the index of level of fuel on the dashboard.