Mazda 323

since 1985 of release

Repair and car operation


Mazda 323

+ Introduction
+ Petrol engines
+ System of greasing of the engine
+ System of cooling of the engine
+ ignition System
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and steering system
+ Brake system
+ Wheels and tires, body, car coloring, care of the car
+ electric equipment System
+ Heater, lighting system, devices
- Governing bodies and operation receptions
   Before landing in the car
   Running in
   Keys
   Locks of doors
   The uniform (central) locking device (if is available)
   Protection against pranks of children (if is available, only on back doors)
   Electric window regulator (if is available)
   Back rotary glasses (on 3-door models)
   Seats
   Adjustment of height of a steering wheel (if is available)
   Seat belts (if is available)
   Door back/trunk lid
   Fuelling
   Mirrors
   Luggage belts
   Trunk lid (if is available)
   Spare wheel
   Dashboard
   + Steering wheel and gear shifting
+ Electric circuits



Seat belts (if is available)

Seat belts with the automatic involving device

For decrease in danger to be traumatized at failure or emergency braking all passengers should be always fastened by available seat belts. Forward belts with three points of fastening are equipped with the lock device. Thanks to belts with the involving device landing and disembarkation of passengers is facilitated and the comfort improves. At big force of delay, for example, at sharp braking, belts are automatically blocked to protect passengers from traumas.

If at a pulling the belt was blocked, it again needs to be cleaned, before it can be extended for desirable length.

Seat belts should be replaced after each strong impact on them, for example, after failure.

Seat belts of forward seats

Pristegivaniye of belts

 PERFORMANCE ORDER

    Take the lock of a belt and a plug-in uvula. Slowly extend a belt. Insert a uvula into the belt lock that it was latched.
    Tighten the lower part of a belt as it is possible more deeply on hips that you in case of failure could not slip under a belt. Stretch a belt through a uvula so that it adjoined to a body. Automatic equipment of retraction will automatically involve the weakened tape of a belt.

Never impose a belt near at hand, round a neck or on an internal shoulder, otherwise, protective influence essentially decreases.

Seat belt removal

 PERFORMANCE ORDER

    For removal of a seat belt press the button on the belt lock.

Seat belts of a back seat (with the involving device)

Corrected addresses same, as well as for forward seat belts.

(without the involving device)

Type A

Pristegivaniye of seat belts

 PERFORMANCE ORDER

    Take the lock of a belt and a uvula. Insert a uvula into the belt lock that it was latched.
    Adjust, if it is necessary, length of a belt. For this purpose hold a regulator at right angle to a belt and pull it to extend a belt. If to pull for the weakened end of a belt, the belt will be truncated.
    Impose the lower part of a belt as it is possible more deeply on hips.

Suspension bracket of three-dot seat belts

 PERFORMANCE ORDER

    Suspend a uvula on a hook of a cover of fastening of a belt if the belt is not used.

Type B

Pristegivaniye of seat belts

 PERFORMANCE ORDER

    Impose the lower part of a belt as it is possible more deeply on hips and adjust length of a belt. For this purpose hold a belt uvula at right angle to a belt and pull it to extend a belt. If to pull for the weakened end of a belt, the belt will be truncated.

Seat belt removal

 PERFORMANCE ORDER

    For removal of a seat belt press the button on the belt lock.

Governed the address and care of system of seat belts

For achievement of the maximum protective influence of system of seat belts observe, please, the next moments:

    Never to be fastened by one belt to two passengers. Watch, that the tape of a belt was not braided. Hold belts and other parts of system far away from sharp edges and subjects which can damage. Check through equal intervals a fabric of belts, locking details, points of fastening and other details of a belt on wear, damages and weak places. The damaged details at once replace. For cleaning of a belt use soft solutions of soap or soft detergents. It is not recommended to clear belts such himikaliya as тетрахлорметан or gasoline, and also to bleach or tint a belt fabric. On belts it should not be made any changes or additions. After belt use, it is necessary to be convinced that it was not hooked for control levers or other subjects.






QX4.ONLINE
S40.ONLINE
A-8.ONLINE
W124.ONLINE
RX300.ONLINE
W140.ONLINE
B3-B4.SPACE
B3B4.SPACE
A-8.SPACE