Mazda 323
+ Introduction
+ Petrol engines
+ System of greasing of the engine
- System of cooling of the engine
Contour of cooling liquid
Antifrizny concentrate
Replacement of cooling liquid
Check of tightness of system of cooling
Removal and thermostat installation/check
Removal and installation of the water pump
Removal and radiator installation
Removal and installation of the motor of the fan
Thermoswitch check
+ ignition System
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and steering system
+ Brake system
+ Wheels and tires, body, car coloring, care of the car
+ electric equipment System
+ Heater, lighting system, devices
+ Governing bodies and operation receptions
+ Electric circuits
|
Removal and radiator installation
After long operation of the car thin channels in a radiator can get littered because of the remains of cooling liquid and lime adjournment. It conducts to falling of capacity of cooling, the engine overheats. Only radiator replacement in this case will rescue.
Removal
|
|
To disconnect a weight cable from the battery.
If is available, to unscrew the resonant chamber.
To merge cooling liquid.
To disconnect the top and bottom hoses on a radiator, previously having weakened and having completely shifted collars.
To disconnect a hose to a broad tank from a radiator, previously having weakened a collar.
To disconnect a cable of the fan of a radiator.
Diesel engine: To disconnect the sensor of level of cooling liquid.
Cars with an automatic transmission: To disconnect pipelines from a maslookhladitel, previously having weakened and having completely shifted collars. To stop up hoses with pure bolts.
To unscrew bolts of fastening of the top holder of a radiator, to incline a radiator back and to take out together with the fan.
If there is no place, it is possible to remove the radiator fan.
|
|
Plates of a radiator have very keen edges therefore at removal it is recommended to work in mittens. |
|
|
If the radiator remains 48 hours removed more long, it is necessary for washing out pure water, to dry the compressed air and to close openings. The radiator can be stored and filled with cooling liquid, having closed openings. If it not to make, corrosion is formed that further conducts to a leakage. |
|
|
Installation
|
|
If it is required, to rearrange the fan on a new radiator.
|
|
If the old radiator is established, it should be checked previously. To check, that in a grid of a radiator and a water-proof casing there were no damages.
|
If погнуты, them it is necessary to level radiator plates carefully a screw-driver.
To check all hoses of cooling liquid on existence of anguishes, cracks and other damages if it is required, to replace. To check a condition of rubber tips of fastening of a radiator.
To insert a radiator from above so that pins of fastening of a radiator entered into rubber nozzles from below on the holder.
To incline a radiator forward, to establish the top holder and to tighten fastening bolts with effort of 10 Nanometers.
To put on the top and bottom hoses of a radiator and to fix them collars.
To put on a hose of cooling liquid to a broad tank and to fix it a collar.
To connect cables to a thermoswitch and the fan.
Diesel engine: To connect a cable to the sensor of level of cooling liquid.
Cars with an automatic transmission: To take out from hoses bolts, to put on hoses on a maslookhladitel and to fix collars. To check liquid level in an automatic transmission, see. Head Introduction.
To fill in cooling liquid, see. Section Routine maintenance.
To connect a weight cable to the battery.
If are available, to establish time on hours and to set a protective code of a radio receiver.
To warm up the engine and to check tightness of shlangovy connections and a radiator.
To check level of cooling liquid, if necessary to add.
|
|
|
|