Mazda 323

since 1985 of release

Repair and car operation



Mazda 323

+ Introduction
+ Petrol engines
+ System of greasing of the engine
+ System of cooling of the engine
+ ignition System
- Power supply system, carburetor, system of injection of fuel
   Purity rules at work with a power supply system
   Removal and sensor installation/check in a fuel tank
   Removal and installation of a fuel tank
   Removal and installation of the fuel pump
   Removal and installation/check of the fuel pump
   Removal and installation of the air filter
   - Carburetor
      Carburetor adjustment
      Malfunctions in system of supply of fuel
      The carburetor with a falling stream and consecutive turning on of chambers
      Check and contents adjustment WITH
      Check/removal and installation of the valve of interruption of supply of fuel
      Check/removal and installation of automatic equipment of cold start
      Removal and carburetor installation
   + System of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and steering system
+ Brake system
+ Wheels and tires, body, car coloring, care of the car
+ electric equipment System
+ Heater, lighting system, devices
+ Governing bodies and operation receptions
+ Electric circuits






Check and contents adjustment WITH

As the contents WITH and number of turns of idling influence together, to be checked and be regulated they should at the same time.

During idling and contents check ABOUT the electrofan of a radiator should not join. If the fan turned on, it is necessary to wait, while it will not be switched off.

Check condition: To check system of production of the fulfilled gases, for this purpose to close a back exhaust pipe a rag. All connections of pipes should be tight.

At this check to pay special attention to good ventilation, differently there is a danger of poisoning.


 PERFORMANCE ORDER

  1. To check люфт drafts and shaft on the carburetor, if necessary to repair or adjust.
  2. To warm up and muffle the engine. The bottom hose on a radiator should be warm.
  3. To disconnect consumers of the electric power.
  4. To check the ignition moment, if necessary to adjust.
  5. The element of the air filter should be pure. Adjustment is best of all for making with a new filtering element.
  6. To connect a tachometer and the measurement device WITH it agrees instructions, the air filter to leave screwed.
  7. To start the heated-up engine and to leave to work at single turns.
  8. To check tightness of an inlet path. For this purpose to put on all connections of system of an admission gasoline by means of a brush If thus number of turns increase, by some time, means, the engine подсасывает extraneous air. To define and eliminate not tight places.

Not to inhale fumes of fuel — they are poisonous! Not to allow gasoline hit on the heated details and ignition system. Inflammably!

  1. To check number of turns of idling.
  1. If value does not correspond demanded, to adjust number of turns of idling by the adjusting screw - 2-.
  1. To check the contents WITH, demanded values see at the end of head.
  2. At a contents deviation WITH from demanded value to remove a seal from the adjusting screw. For this purpose to do in a seal an opening, to screw a suitable screw or the screw саморез and to take out the screw together with a seal. If necessary to remove a seal by means of nippers.
  3. To adjust the contents WITH rotation of the adjusting screw-1-.
  4. To insert a new seal.
  5. To disconnect measuring devices.

Number of turns of idling and the contents WITH

Engine The contents WITH Number of turns of idling
Е1, ЕЗ, Е5 1,5 — 2,0 %

Mechanical transmission: 850 ± 50 rpm

Automatic transmission: 950 ± 50 rpm

ВЗ 0,7 — 1,5 %
В5 1,5 — 2,0 %
In 6 0,7 — 1,5 %