Mazda 323

since 1985 of release

Repair and car operation



Mazda 323

+ Introduction
+ Petrol engines
+ System of greasing of the engine
+ System of cooling of the engine
+ ignition System
- Power supply system, carburetor, system of injection of fuel
   Purity rules at work with a power supply system
   Removal and sensor installation/check in a fuel tank
   Removal and installation of a fuel tank
   Removal and installation of the fuel pump
   Removal and installation/check of the fuel pump
   Removal and installation of the air filter
   + Carburettor
   - System of injection of fuel
      System of injection of fuel
      Memory of malfunctions
      Security measures at work with injection system
      Idling check
      Verification of the contents WITH
      Check/adjustment of the sensor of a butterfly valve
      Removal and installation/check of the sensor of temperature of cooling liquid
      Check of gates of injection (injectors)
      Removal and installation of gates of injection
      Check of the fuel pump
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and steering system
+ Brake system
+ Wheels and tires, body, car coloring, care of the car
+ electric equipment System
+ Heater, lighting system, devices
+ Governing bodies and operation receptions
+ Electric circuits






Removal and installation of gates of injection

Removal

 PERFORMANCE ORDER

  1. To disconnect a weight cable from the battery.

Data from memory of malfunctions of the engine or protective code of a radio receiver are thus erased. Before shutdown of the battery it is necessary to read instructions in the Section Removal and battery installation.

  1. To reduce pressure of fuel.
  2. To remove an inlet hose between the air filter and a butterfly valve branch pipe.
  3. To disconnect a gas drive on the butterfly valve lever.
  1. For the best dismantle to remove the case of an inlet collector-1-, previously having disconnected vacuum pipelines and for simplification of installation having marked with a sticky tape.
  1. To disconnect a vacuum hose from a regulator of pressure of fuel.
  2. To disconnect tips of-3-gates of injection and to put a cable plait aside.
  3. To disconnect submitting and returnable топливопроводы-2-on the fuel highway, having weakened previously a collar.

Fuel is in the pipeline under pressure. For protection against a razbryzgivaniye to cover the pipeline with a rag.

  1. To turn out bolts of fastening of the distributive fuel highway-4-.
  2. To remove the distributive highway-4-with gates of injection-5-.

The distributive highway to remove carefully that gates of injection did not drop out and were not damaged.

  1. To take out injection gates from the distributive highway.
  2. To take out insulators from openings of gates.

Installation

Rings, and insulators of gates of injection it is necessary to replace laying always.


 PERFORMANCE ORDER

  1. To insert injection gates with new consolidations of round section into the top part of the distributive highway. Previously to cover consolidations by a small amount of oil.
  2. To insert insulators into openings of gates.
  1. To establish the distributive fuel highway with injection gates in a head of cylinders.
  1. To check, that injection gates easily turned. Otherwise again to remove gates and to check the provision of consolidations of round section.
  2. To turn injection gates so that tips were turned up.
  3. To establish bolts of fastening of the distributive fuel highway and to tighten with effort of 25 Nanometers.
  4. To put on a regulator of pressure of fuel a vacuum hose.
  5. To connect submitting and returnable pipelines and to fix collars.
  6. To lay a cable plait to gates of injection and to connect tips.
  7. To establish the case of an inlet collector with new laying and to screw with effort of 25 Nanometers. To put on vacuum pipelines according to marking.
  8. To attach a gas drive to the butterfly valve lever.
  9. To put on an inlet hose a branch pipe of a butterfly valve and to fix a collar.
  10. To connect the tip of the fuel pump and to establish a back seat.
  11. To connect a weight cable to the battery.
  12. If are available, to establish time on hours and to set a protective code of a radio receiver.