Mazda 323

since 1985 of release

Repair and car operation


Mazda 323

+ Introduction
- Petrol engines
   Specifications
   Removal and engine installation
   Removal and installation of a gear belt of VZ engines, В5, B6 (SOHC), (SOHC) VR
   Removal and installation of a gear belt (DOHC)
   Removal and head installation cylinders/replacement of laying of a head of cylinders
   Mechanism of a chain drive
   Removal and installation cam-shaft/adjustment of phases of a gazoraspredeleniye
   Removal and camshaft installation
   Cam-shaft/drive of the distributive mechanism
   Distributive shaft/drive of the distributive mechanism
   Removal and installation of camshafts
   Removal and installation of valves
   Replacement of maslootrazhatelny caps
   Check of directing valves
   Processing of facets of saddles of valves in a head cylinders/processing of valves
   Grinding in of valves
   Check/adjustment of a gap of valves
   Compression check
   Removal and installation/tension of a maple belt
+ System of greasing of the engine
+ System of cooling of the engine
+ ignition System
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and steering system
+ Brake system
+ Wheels and tires, body, car coloring, care of the car
+ electric equipment System
+ Heater, lighting system, devices
+ Governing bodies and operation receptions
+ Electric circuits



Removal and installation/tension of a maple belt

If the belt is established old maple, it always should be checked on wear and damages. If lateral surfaces are worn-out, there are cracks and gaps, in any case it is necessary to replace a belt. At installation to watch, that the belt correctly adjoined to all pulleys.

Maple belt of the generator and water pump

 PERFORMANCE ORDER

    To weaken the adjusting screw and a fastening bolt.
    To incline the generator to the engine and to remove maple a belt. To impose a new belt and to tighten a nut and the lock screw. To check a tension between pulleys of the generator and the water pump - an arrow-. At influence with strength of 100 N (10 kg) that approximately corresponds to pressing a thumb, to measure the belt deflection, demanded values see in the table.
Engine designation deflection in mm
new belt the belt which was in the use
Е1, ЕЗ, Е5 12 — 13 13 — 14
ВЗ, В5, В6 8 — 9 9 — 10
PN (Diesel engine) 9 — 10 10 — 10, 5
    To screw an adjusting bolt with effort of 25 Nanometers, a fastening bolt with effort of 50 Nanometers.

Maple belt сервонасоса (petrol engine)

 PERFORMANCE ORDER

    To weaken a lock nut and a fastening bolt.
    To turn an adjusting bolt that it was possible to remove maple a belt. To remove maple a belt. To impose maple a belt to adjust a tension a bolt. To check a tension between pulleys of the crankshaft and the oil pump of a servoupravleniye - an arrow-. At influence with strength of 100 N (10 kg) that approximately corresponds to the thumb pressing, the new belt should cave in on 8-9 mm, the belt which was in the use on 9-10 mm. To tighten a lock nut with effort of 25 Nanometers, a fastening bolt with effort of 45 Nanometers.

Maple belt сервонасоса and conditioner compressor (the petrol engine)

 PERFORMANCE ORDER

    To weaken a lock nut and a fastening bolt.
    To turn an adjusting bolt that it was possible to remove maple a belt. To remove a belt. To establish a new belt and to adjust a tension an adjusting bolt. To check a tension between pulleys of the crankshaft and the oil pump of a servoupravleniye - an arrow-. At influence with strength of 100 N (10 kg) that approximately corresponds to the thumb pressing, the new belt should cave in on 8-9 mm, the belt which was in the use on 9-10 mm.To tighten a lock nut with effort of 25 Nanometers, a fastening bolt with effort of 45 Nanometers.