Mazda 323
+ Introduction
- Petrol engines
Specifications
Removal and engine installation
Removal and installation of a gear belt of VZ engines, В5, B6 (SOHC), (SOHC) VR
Removal and installation of a gear belt (DOHC)
Removal and head installation cylinders/replacement of laying of a head of cylinders
Mechanism of a chain drive
Removal and installation cam-shaft/adjustment of phases of a gazoraspredeleniye
Removal and camshaft installation
Cam-shaft/drive of the distributive mechanism
Distributive shaft/drive of the distributive mechanism
Removal and installation of camshafts
Removal and installation of valves
Replacement of maslootrazhatelny caps
Check of directing valves
Processing of facets of saddles of valves in a head cylinders/processing of valves
Grinding in of valves
Check/adjustment of a gap of valves
Compression check
Removal and installation/tension of a maple belt
+ System of greasing of the engine
+ System of cooling of the engine
+ ignition System
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and steering system
+ Brake system
+ Wheels and tires, body, car coloring, care of the car
+ electric equipment System
+ Heater, lighting system, devices
+ Governing bodies and operation receptions
+ Electric circuits
|
Removal and installation of a gear belt of VZ engines, В5, B6 (SOHC), (SOHC) VR
Removal
|
|
To disconnect a weight cable from the battery.
To lift the car and to remove the right forward wheel.
To remove the bottom guard of the engine in the right niche of a wheel.
If is available, to remove maple a belt of the pump of a servoupravleniye and the conditioner compressor, see. Section Removal and installation/tension of a maple belt.
To weaken bolts of fastening of a belt pulley of the water pump.
To remove maple a generator belt, see. Section Removal and installation/tension of a maple belt.
To turn out bolts of fastening of a belt pulley of the water pump and to remove a pulley.
|
|
To 2/91 g вып.
|
|
To block the crankshaft and to unscrew bolts of fastening of a belt pulley of the crankshaft.
For blocking of the crankshaft to include the 5th transfer and to ask the assistant to squeeze out a brake pedal.
To remove a washer, a remenny pulley of the crankshaft, external and internal directing disks of a gear belt.
|
|
With 3/91 g вып.
|
|
To unscrew bolts of fastening of a belt pulley of the crankshaft. To hold a neck of a belt pulley the special MAZDA ZZT 490011102 adaptation.
To unscrew the top and bottom casings of a gear belt.
|
|
To disconnect tips of candles and to remove spark plugs, see. Head Introduction.
|
To establish the piston of the 1st cylinder in the provision of ignition. For this purpose to turn the crankshaft that labels on a belt pulley of a cam-shaft coincided with labels on a cover of the distributive mechanism and a head of cylinders. Labels on the block of cylinders and on a crankshaft cogwheel at the same time should coincide.
For a provorachivaniye of the crankshaft to include the 5th transfer and to shift the car on an equal surface. Other possibility to turn crankshaft: To raise a forward wheel, to include the 5th transfer and to turn a wheel a hand.
|
|
After the piston of the 1st cylinder will be in the provision of ignition, to establish a transmission in neutral situation and once again to check, whether labels on a belt pulley of the crankshaft and a cover of a drive of the distributive mechanism coincide. If labels coincide, not to turn at all more crankshaft. |
|
|
If the old gear belt is established again, it is necessary to mark it. On a belt it is necessary to put to the shooter specifying the direction of rotation. The crankshaft rotates in the direction clockwise.
|
|
|
To weaken a bolt of a tension roller and to wring out a tension roller in the arrow direction while the gear belt will not be weakened. Again to tighten a bolt of a tension roller.
|
To remove a gear belt after that the provision of cogwheels not to change.
|
|
Installation
|
|
Not to bend and not to overwind a gear belt. The polluted, damaged or worn-out gear belt in any case to replace. To check uniformity and ease of a course of a tension roller. |
|
|
If the cam-shaft turns at the removed gear belt, any piston should not be in the situation BMT. Otherwise there can be serious damages of pistons and valves. If it is required to turn the crankshaft, previously it is necessary to establish all pistons polovinny height. For this purpose to put from above on a crankshaft cogwheel the line with chalk (a condition: the crankshaft is in the position BMT of the piston of the 1st cylinder), then to turn a crankshaft wheel on 1/2 turns to the left or to the right. The mark chalk is in horizontal situation. |
|
|
To be convinced that the cam-shaft is in the situation relevant to VMT of the 1st cylinder. Labels on a wheel of a cam-shaft and on a cover of a drive of the distributive mechanism and a head of cylinders thus should coincide.
|
|
At the same time the mark in a cogwheel of the crankshaft should coincide with a mark in the block of cylinders. Then the piston of the 1st cylinder is in situation VMT.
|
|
|
To impose a gear belt so that the pulling party was tense. If the old belt is established, to pay attention to the direction of its rotation.
|
|
|
At installation of a gear belt the provision of distributive and cranked shaft should not change. Otherwise in the engine there can be serious malfunctions, or the engine will not develop the maximum capacity. |
To weaken a bolt of a tension roller that the roller adjoined to a belt.
To turn the crankshaft two times in the direction of rotation and once again to check coincidence of labels, if necessary to repeat adjustment.
To tighten a bolt of fastening of a tension roller with effort of 20 Nanometers.
Two times to turn the crankshaft in the direction of rotation and once again to check adjustment.
|
|
To check a tension of a gear belt. The gear belt on the longest site at influence with force of 10 kg that corresponds to pressing a thumb, should cave in on 11-13 mm. If value does not correspond demanded, it is necessary to weaken a tension roller and to tighten it again.
|
To screw the top and bottom casings of a gear belt with effort of 10 Nanometers.
To establish external and internal directing disks of a gear belt according to dredging on a crankshaft wheel. To consider adjusting situation.
|
|
To 2/91 g вып.
|
|
To establish a remenny pulley of the crankshaft and a washer-5-and to tighten fastening bolts with effort of 15 Nanometers.
|
|
With 3/91 g вып.
|
|
To establish a bolt of fastening of a belt pulley of the crankshaft. Holding a pulley neck the special MAZDA SST 49 adaptation D 011102 and to tighten a bolt with effort of 165 Nanometers.
To establish a remenny pulley of the water pump and to tighten fastening bolts with effort of a hand.
To establish a maple belt, see. Section Removal and installation/tension of a maple belt.
To tighten a remenny pulley of the water pump with effort of 10 Nanometers.
To establish candles and to connect cables, see. Head Introduction.
To screw a guard in the right niche of a wheel.
To establish a forward wheel and to lower the car.
To connect a weight cable to the battery.
If are available, to establish time on hours and to set a protective code of a radio receiver.
To check the ignition moment, if necessary to adjust, see. Head ignition System, Section Check/adjustment of the moment of ignition.
|
|
|
|
