Mazda 323
+ Introduction
+ Petrol engines
+ System of greasing of the engine
+ System of cooling of the engine
+ ignition System
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
- Suspension bracket and steering system
Forward suspension bracket — the general information
Removal and installation of an amortization rack
Dismantling amortization rack/removal and shock-absorber installation / screw spring
Shock-absorber check
Removal and installation cross-section lever/replacement of a rubber support
Check/replacement of a support of the cross-section lever / rotary fist
Removal and installation of a power shaft
Removal and installation of an intermediate shaft
Check/dismantling driving shaft/replacement of cuffs
Bearing of a forward nave
Back suspension bracket
Removal and installation of a back amortization rack
Dismantling back amortization rack/removal and shock-absorber installation / screw spring
Cross-section levers / longitudinal lever/stabilizer
Check of the bearing of a nave
Removal and installation of the bearing of a nave
Adjustment люфта nave bearing
Removal and nave installation
Steering
Removal and installation of a steering wheel
Removal and installation of a tip of steering draft
Removal and installation of a rubber cuff of a steering drive
Servoupravleniye pump
Corners of installation of wheels
Values for MAZDA 323 check
+ Brake system
+ Wheels and tires, body, car coloring, care of the car
+ electric equipment System
+ Heater, lighting system, devices
+ Governing bodies and operation receptions
+ Electric circuits
|
Removal and installation of a back amortization rack Removal
|
|
If necessary to remove a lateral upholstery in salon, to reach the top bolts of an amortization rack.
To weaken nuts of wheels of the car standing on the earth.
To change the provision of a disk of a wheel concerning a nave that it was possible to establish an otbalansirovanny wheel in former situation.
To lift a back part of the car.
To remove a wheel.
|
|
Only full drive: To unscrew a bolt - And - by which the longitudinal lever on a suspension bracket beam is fixed. Then to weaken a bolt - In - without unscrewing. If is available, in addition to unscrew an air hose of system of adjustment of height of a road gleam on the shock-absorber from above.
|
To remove a bracket-1-and to release a brake hose from the holder on an amortization rack. | Not to unscrew a brake hose. |
To prop up a suspension bracket beam a support or the hydraulic lift that it did not fall down when weakening an amortization rack.
|
|
To unscrew 2 nuts-2-amortization racks on a suspension bracket beam, to remove bolts-3-.
|
To unscrew 2 nuts on the top support of an amortization rack and to take out an amortization rack-5-.
If necessary to disassemble an amortization rack, see. Head Dismantling back amortization rack/removal and shock-absorber installation / screw spring.
|
|
Installation
|
|
To insert an amortization rack, to tighten 2 top nuts with effort of 30 Nanometers.
To insert 2 bolts of an amortization rack on a beam in front back, to tighten nuts with effort of 110 Nanometers.
To clean from under a beam the lift.
To strengthen on an amortization rack a brake hose.
Only full drive: To tighten bolts - And - and - In - with effort of 70 Nanometers. In the presence of system of adjustment of height of a road gleam to screw an air hose from above on the shock-absorber with effort of 20 Nanometers.
To screw a wheel, thus considering a label on a nave. To lower the car and to tighten nuts of wheels cross-wise with effort of 100 Nanometers.
If it is removed, to establish an internal upholstery over an amortization rack.
To make measurements of corners of installation of wheels.
|
|
|
|