Mazda 323
+ Introduction + Petrol engines + System of greasing of the engine + System of cooling of the engine + ignition System + Power supply system, carburetor, system of injection of fuel + Diesel engine + System of production of the fulfilled gases + Coupling + Manual transmission + Automatic transmission - Suspension bracket and steering system Forward suspension bracket — the general information Removal and installation of an amortization rack Dismantling amortization rack/removal and shock-absorber installation / screw spring Shock-absorber check Removal and installation cross-section lever/replacement of a rubber support Check/replacement of a support of the cross-section lever / rotary fist Removal and installation of a power shaft Removal and installation of an intermediate shaft Check/dismantling driving shaft/replacement of cuffs Bearing of a forward nave Back suspension bracket Removal and installation of a back amortization rack Dismantling back amortization rack/removal and shock-absorber installation / screw spring Cross-section levers / longitudinal lever/stabilizer Check of the bearing of a nave Removal and installation of the bearing of a nave Adjustment люфта nave bearing Removal and nave installation Steering Removal and installation of a steering wheel Removal and installation of a tip of steering draft Removal and installation of a rubber cuff of a steering drive Servoupravleniye pump Corners of installation of wheels Values for MAZDA 323 check + Brake system + Wheels and tires, body, car coloring, care of the car + electric equipment System + Heater, lighting system, devices + Governing bodies and operation receptions + Electric circuits
|
Removal and installation cross-section lever/replacement of a rubber support As for an inhaling of rubber support the car should stand on wheels, is necessary or the lift with a platform, or a viewing hole.
Removal
|
to grease (lithium universal greasing) |
|
To mark the provision of a disk of a wheel in relation to a nave that it was possible to establish an otbalansirovanny wheel in former situation.
To weaken nuts of forward wheels of the car standing on the earth.
To lift the car.
To remove forward wheels.
To weaken a stabilizer support on the cross-section lever for what to unscrew a nut-1-and to remove a bolt-3-with intermediate elements-2-. On cars to 9/89 g вып. and all versatile person models the bolt contrary to the image, is established from top to down.
To unscrew a bolt-4-on a forward support of the cross-section lever.
To unscrew a collar on a back support of the lever (a bolt-5-).
To weaken a nut-6-, to take out a bolt-6-on a rotary fist. To take out a pin of a spherical support down from a rotary fist and to remove the lever.
|
If the pin of a spherical support is not taken out by a hand, to insert mount between the hinge and a rotary fist. Not to damage thus a hinge cuff, to enclose a rag. |
|
|
Installation
|
To check wear of support of the lever and a rotary fist, if necessary to replace, see. Head Check/replacement of a support of the cross-section lever / rotary fist.
To insert the cross-section lever on a body and a rotary fist, to wrap bolts and nuts a hand, yet without tightening.
To screw the stabilizer, without tightening bolts of fastening it is final.
To screw a wheel, considering the labels put at removal. To lower the car and to tighten wheel nuts cross-wise with effort of 100 Nanometers.
Several times to rock the car that the suspension bracket of wheels settled.
|
Models to 9/89 g вып. and versatile person models: To screw a stabilizer nut while the length of an acting carving does not become equal 10,8 mm. | | Models from 10/89 g вып., except "versatile person": To screw a stabilizer nut while the length of an acting carving will not lie within 17 — 19 mm.
|
To tighten back and forward support of the cross-section lever with effort of 110 Nanometers, a bolt on a rotary fist with effort of 60 Nanometers.
Whenever possible it is rather to measure corners of installation of wheels in a workshop.
|
|
|
|